View BNC-P-3-NICAU-CF_8846062.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

bnc series bnc style connector 150116 j is-c-5412,mil-prf-39012,dsp-c-6202 frequency range dc to 2ghz 50 lock type bayonet characteristic impedance conforming standard 3p)4 $pnqmjbou 3p)4 $pnqmjbou item material / finish shell (body) copper alloy / ni or ag plating contact (male) copper alloy / ag or au plating contact (female) copper alloy / ag or au plating insulator ptfe gasket silicon rubber characteristic impedance 50 rated voltage 500vac(r.m.s.) dielectric withstanding voltage 1500v ac(r.m.s.) for 1 minute insulation resistance 1000m mim. at 500v dc contact resistance 3m max. v.s.w.r. 1.3 max. at dc to 2ghz operating temperature -55 ? +85 specifications the specifcations are typical but may not apply to all connectors. and if the cable is not 50 , the specifcation will be changed. please check the specifcations on each item with its drawing from us when you use. ?bnc style 50 ohm rf connector ?50 ohm impedance design ?quick mate/demate with reliable bayonet coupling ?high reliability interconnect for numerous connect and disconnect cycles. ?bnc 50 ohm connector is intermateable with bnc75 (75 ohm) styl e connector. ?bnc is capable of mating with 75 ohm cable for frequencies less than 200mhz. ?frequencies higher t han 200mhz should use ddks bnc75 series connector. material/finish feature outline ddks 50 ohm bnc bayonet rf connector are available in several configurations to support a variety of design alternatives. these bnc connectors are available in straight, right angle and panel mount confgurations. http://www.ddknet.co.jp please acknowledge that the specifcation etc. of this catalog might change by the improvement etc. without notice. moreover, the characteristic and the specifcation of the published product are the reference values. please confrm the content with the latest delivery specifcations when you use the product.
2 sraight cable plug part number applicable cable a l finish assembly instruction outer conductor center conductor bnc-p-3-cf 3d-2v 6.4 25.0 ag ag 1 3c-2v bnc-p-3-ni-cf 3d-2v 6.4 25.0 ni ag 1 3c-2v BNC-P-3-NICAU-CF 3d-2v 6.4 25.0 ni au 1 3c-2v bnc-p-58u-cf rg-55/u 5.4 27.0 ag ag 1 rg-58/u bnc-p-58u-ni-cf rg-55/u 5.4 27.0 ni ag 1 rg-58/u bnc-p-62u ` cf rg-62/u 6.6 26.2 ag ag 1 bnc-p-62u-ni-cf rg-62/u 6.6 26,2 ni ag 1 ug-260/u-cf rg-59/u 6.55 24.6 ag ag 1 rg-62/u ug-260/u-ni-cf rg-59/u 6.55 24.6 ni ag 1 rg-62/u part number applicable cable a l finish assembly instruction outer conductor center conductor clamp type ? bnc-p-3 l 14.5 a bnc-p-3w 14.5 l a bnc-p-5 14.5 a 17.5 l bnc-p-1.5v-cr-cf 14.5 31.7 a 14.5 l a bnc-p-1.5cqew-cr10 14.5 l a bnc-p-3c-cr1 ? bnc-p-3 l 14.5 a bnc-p-3w 1.5 bnc-p-5 14.5 a 17.5 l bnc-p-1.5v-cr-cf 14.5 31.7 a 14.5 l a bnc-p-1.5cqew-cr10 14.5 l a bnc-p-3c-cr1 part number applicable cable a l finish assembly instruction outer conductor center conducto r bnc-p-3w-cf 3d-2w 7.1 29.1 ag ag 1 3c-2w bnc-p-3w-ni-1-cf 3d-2w 7.1 29.1 ni ag 1 3c-2w ? bnc-p-3 l 14.5 a bnc-p-3w 14.5 l a bnc-p-5 14.5 a 17.5 l bnc-p-1.5v-cr-cf 14.5 31.7 a 14.5 l a bnc-p-1.5cqew-cr10 14.5 l a bnc-p-3c-cr1 bnc-p-5-cf 5d-2v 8.6 37.0 ag ag 1 5c-2v bnc-p-5-ni-cf 5d-2v 8.6 37.0 ni ag 1 5c-2v bnc-p-5nicau-cf 5d-2v 8.6 37.0 ni au 1 5c-2v bnc-p-5w-cf 5d-2w 9.2 37.0 ag ag 1 5c-2w bnc-p-5w-ni-cf 5d-2w 9.2 37.0 ni ag 1 5c-2w unitmm http://www.ddknet.co.jp bncseries please acknowledge that the specifcation etc. of this catalog might change by the improvement etc. without notice. moreover, the characteristic and the specifcation of the published product are the reference values. please confrm the content with the latest delivery specifcations when you use the product.
straight cable plug 3 part number applicable cable a finish assembly instruction crimp tool outer conductor center conductor bnc-p-1.5v-cr-cf 1.5d-2v 5.5 ag ag 3 cr-h-1100 1.5c-2v bnc-p-1.5v-cr-ni-cf 1.5d-2v 5.5 ni ag 3 cr-h-1100 1.5c-2v bnc-p-1.5v-cr-nicau-cf 1.5d-2v 5.5 ni au 3 cr-h-1100 1.5c-2v bnc-p-2.5v-cr-cf 2.5d-2v 5.5 ag ag 3 cr-h-1100 2.5c-2v bnc-p-2.5v-cr-ni-cf 2.5d-2v 5.5 ni ag 3 cr-h-1100 2.5c-2v bnc-p-2.5v-cr-nicau-cf 2.5d-2v 5.5 ni au 3 cr-h-1100 2.5c-2v bnc-p-179u-cr-cf rg-179/u 5.5 ag ag 3 cr-h-1100 bnc-p-179u-cr-ni-cf rg-179/u 5.5 ni ag 3 cr-h-1100 crimp type ? bnc-p-3 l 14.5 a bnc-p-3w 14.5 l a bnc-p-5 14.5 a 17.5 l bnc-p-1.5v-cr-cf 14.5 31.7 a 14.5 l a bnc-p-1.5cqew-cr10 14.5 l a bnc-p-3c-cr1 part number applicable cable a l finish assembly instruction crimp tool note outer conductor center conductor bnc-p-1.5cqew-cr10-cf 1.5c-qew 5.5 24.3 ni au ` cr-h-1100 delta-mate bnc-p-1.5d-cr10-cf 1.5d-xv 4.0 23.3 ni au 4 cr-h-1120a delta-mate 1.5d-qew bnc-p-3c-cr10-boot-cf 3c-2v 7.1 24.3 ni au 4 cr-h-1116 delta-mate bnc-p-3d-cr10-boot-cf 3d-2v 7.1 24.3 ni au 4 cr-h-1116 delta-mate bnc-p-58u-cr10-cf rg-58/u 6.3 24.3 ni au 4 cr-h-1115 delta-mate rg-58a/u bnc-p-3d-cr10-cf 3d-2v 7.1 24.3 ni au 4 cr-h-1116 delta-mate part number applicable cable a l finish assembly instruction crimp tool outer conductor center conductor bnc-p-3c-cr1-cf 3c-2v 7.0 28.0 ag ag 2 cr-h-1102 bnc-p-3c-cr1-ni-cf 3c-2v 7.0 28.0 ni ag 2 cr-h-1102 ? bnc-p-3 l 14.5 a bnc-p-3w 14.5 l a bnc-p-5 14.5 a 17.5 l bnc-p-1.5v-cr-cf 14.5 31.7 a 14.5 l a bnc-p-1.5cqew-cr10 14.5 l a bnc-p-3c-cr1 ? bnc-p-3 l 14.5 a bnc-p-3w 14.5 l a bnc-p-5 14.5 a 17.5 l bnc-p-1.5v-cr-cf 14.5 31.7 a 14.5 l a bnc-p-1.5cqew-cr10 1.5 bnc-p-3c-cr1 6ojunn iuuqxxxeelofudpkq #/$y4fsjft ? 1mfbtfbdlopxmfehfuibuuiftqfdjpdbujpofudpguijtdbubmphnjhiudibohfczuifjnqspwfnfoufudxjuipvuopujdf y.psfpwfs uifdibsbdufsjtujdboeuiftqfdjpdbujpopguifqvcmjtifeqspevdubsfuifsfgfsfodfwbmvft y1mfbtfdpopsnuifdpoufouxjuiuifmbuftuefmjwfsztqfdjpdbujpotxifozpvvtfuifqspevdu
right angle cable plug 4 clamp type part number applicable cable a finish assembly instruction outer conductor center conductor bnc-lp-3-cf 3d-2v 6.4 ag ag 5 3c-2v bnc-lp-3-cau-cf 3d-2v 6.4 ag au 5 3c-2v bnc-lp-3-nicau-cf 3d-2v 6.4 ni au 5 3c-2v bnc-lp-3-ni-cf 3d-2v 6.4 ni ag 5 3c-2v bnc-lp-58u-cf rg-55/u 5.38 ag ag 6 rg-58/u bnc-lp-58u-ni-cf rg-55/u 5.38 ni ag 6 rg-58/u bnc-lp-55u-cf rg-55/u 5.4 ag ag 6 rg-58/u part number applicable cable finish assembly instruction outer conductor center conductor bnc-lp-5-cf 5d-2v ag ag 7 5c-2v bnc-lp-5-ni-cf 5d-2v ni au 7 5c-2v ???? bnc-lp-3 33 a 25 27 33 bnc-lp-5 ? l a bnc-j-3 ????bnc-pj-3 l a 2.3 15.8 12.7 12.7 17.5 4-b 12.7 0.05 12.7 0.05 11.5 +0.1 0 4-3.0 +0.1 0 80% ???? bnc-lp-3 33 a 25 27 33 bnc-lp-5 ? l a bnc-j-3 ????bnc-pj-3 l a 2.3 15.8 12.7 12.7 17.5 4-b 12.7 0.05 12.7 0.05 11.5 +0.1 0 4-3.0 +0.1 0 80% straight cable jack clamp type part number applicable cable a (l) finish assembly instruction outer conductor center conductor bnc-j-3-cf 3d-2v 6.4 28.5 ag ag 1 3c-2v bnc-j-3-ni-cf 3d-2v 6.4 28.5 ni ag 1 3c-2v bnc-j-58u-cf rg-55/u 5.4 28.6 ag ag 1 rg-58/u ???? bnc-lp-3 33 a 25 27 33 bnc-lp-5 ? l a bnc-j-3 ????bnc-pj-3 l a 2.3 15.8 12.7 12.7 17.5 4-b 12.7 0.05 12.7 0.05 11.5 +0.1 0 4-3.0 +0.1 0 80% unitmm http://www.ddknet.co.jp bncseries please acknowledge that the specifcation etc. of this catalog might change by the improvement etc. without notice. moreover, the characteristic and the specifcation of the published product are the reference values. please confrm the content with the latest delivery specifcations when you use the product.
straight panel cable jack 5 part number b finish outer conductor center conductor bnc-r-cf 3.1 ag ag bnc-r-ni-cf 3.1 ni ag ug-290/u-cf m2.6 ag ag ug-290/u-ni-1-cf m2.6 ni ag part number applicable cable a b (l) finish assembly instruction outer conductor center conductor bnc-pj-3-cf 3d-2v 6.4 3.0 28.5 ag ag 1 3c-2v bnc-pj-3-ni-cf 3d-2v 6.4 3.0 28.5 ni ag 1 3c-2v bnc-pj-58u-cf rg-55/u 5.4 3.0 28.5 ag ag 1 rg-58/u bnc-pj-58u-ni-cf rg-55/u 5.4 3.0 28.5 ni ag 1 rg-58/u bnc-pj-58u-nicau-cf rg-55/u 5.4 3.0 28.5 ni au 1 rg-58/u clamp type ???? bnc-lp-3 33 a 25 27 33 bnc-lp-5 ? l a bnc-j-3 ????bnc-pj-3 l a 2.3 15.8 12.7 12.7 17.5 4-b 12.7 0.05 12.7 0.05 11.5 +0.1 0 4-3.0 +0.1 0 80% receptacle jack panel mounting dimensions ?? bnc-r-cf 12.7 12.7 17.5 26.3 15.8 2.3 1.4 12.7 0.05 12.7 0.05 4-3.0 +0.1 0 9.0 +0.1 0 bnc-lr-ni 12.7 23 23 12.7 17.5 4-b 4-3.0 12.7 12.7 4-3.2 9.0 bnc-r-pc-4 15.0 13.3 2.5 2.3 10.16 0.05 5.08 0.025 5.08 0.05 5-1.2 +0.1 0 10.16 +0.1 0 ?? bnc-r-cf 12.7 12.7 17.5 26.3 15.8 2.3 1.4 12.7 0.05 12.7 0.05 4-3.0 +0.1 0 9.0 +0.1 0 bnc-lr-ni 4-b 4- 4- bnc-r-pc-4 15.0 13.3 2.5 2.3 10.16 0.05 5.08 0.025 5.08 0.05 5-1.2 +0.1 0 10.16 +0.1 0 part number finish outer conductor center conductor bnc-lr-cf ag ag bnc-lr-ni-cf ni ag panel mounting dimensions panel mounting dimensions 6ojunn iuuqxxxeelofudpkq #/$y4fsjft ? 1mfbtfbdlopxmfehfuibuuiftqfdjpdbujpofudpguijtdbubmphnjhiudibohfczuifjnqspwfnfoufudxjuipvuopujdf y.psfpwfs uifdibsbdufsjtujdboeuiftqfdjpdbujpopguifqvcmjtifeqspevdubsfuifsfgfsfodfwbmvft y1mfbtfdpopsnuifdpoufouxjuiuifmbuftuefmjwfsztqfdjpdbujpotxifozpvvtfuifqspevdu
receptacle jack 6 ?? bnc-r-cf 12.7 12.7 17.5 26.3 15.8 2.3 1.4 12.7 0.05 12.7 0.05 4-3.0 +0.1 0 9.0 +0.1 0 bnc-lr-ni 12.7 23 23 12.7 17.5 4-b 4-3.0 12.7 12.7 4-3.2 9.0 bnc-r-pc-4 15.0 13.3 2.5 2.3 10.16 0.05 5.08 0.025 5.08 0.05 5-1.2 +0.1 0 10.16 +0.1 0 part number finish note outer conductor center conductor bnc-r-pc-4-ag-cf ni ag board lock is ag plating bnc-r-pc-4-d1-cf ni au board lock is ag plating. part number finish note outer conductor center conductor bnc-lr-pc-4-ag-cf ni ag board lock is ag plating bnc-lr-pc-4-nicau-cf ni au board lock is ag plating bnc-lr-pc-4-ag ?? -2 ?????? bnc-rb2 bnc-pr bnc-625/u 10.16 0.05 5.08 0.025 5.08 0.05 5-1.2 +0.1 0 10.16 +0.1 0 12.7 0.05 12.7 0.05 4-3.0 +0.1 0 9.0 +0.1 0 19.1 23 2.5 10.16 10.16 15.0 12.7 17.5 28.2 17.7 2.3 1.1 26.3 12.7 12.7 12.6 1.5 1.4 10.3 11.3 +0.1 0 10.3 12.7 26.3 12.6 1.5 1.4 11.3 +0.1 0 hex dia.12.7 hex dia.12.7 4-3.0 bnc-lr-pc-4-ag ?? -2 ?????? bnc-rb2 bnc-pr bnc-625/u 10.16 0.05 5.08 0.025 5.08 0.05 5-1.2 +0.1 0 10.16 +0.1 0 12.7 0.05 12.7 0.05 4-3.0 +0.1 0 9.0 +0.1 0 19.1 23 2.5 10.16 10.16 15.0 12.7 17.5 28.2 17.7 2.3 1.1 26.3 12.7 12.7 12.6 1.5 1.4 10.3 11.3 +0.1 0 10.3 12.7 26.3 12.6 1.5 1.4 11.3 +0.1 0 hex dia.12.7 hex dia.12.7 4-3.0 part number finish outer conductor center conductor bnc-pr-cf ag ag bnc-pr-ni-cf ni ag pcb mounting dimensions pcb mounting dimensions panel mounting dimensions unitmm http://www.ddknet.co.jp bncseries please acknowledge that the specifcation etc. of this catalog might change by the improvement etc. without notice. moreover, the characteristic and the specifcation of the published product are the reference values. please confrm the content with the latest delivery specifcations when you use the product.
7 straight bulkhead cable jack part number finish outer conductor center cnductor bnc-rb2-cf ag ag bnc-rb2-ni-cf ni ag bnc-rb2-nicau-cf ni au bnc-lr-pc-4-ag ?? -2 ?????? bnc-rb2 bnc-pr bnc-625/u 10.16 0.05 5.08 0.025 5.08 0.05 5-1.2 +0.1 0 10.16 +0.1 0 12.7 0.05 12.7 0.05 4-3.0 +0.1 0 9.0 +0.1 0 19.1 23 2.5 10.16 10.16 15.0 12.7 17.5 28.2 17.7 2.3 1.1 26.3 12.7 12.7 12.6 1.5 1.4 10.3 11.3 +0.1 0 10.3 12.7 26.3 12.6 1.5 1.4 11.3 +0.1 0 hex dia.12.7 hex dia.12.7 4-3.0 panel thickness1.2 ? 3.5 bnc-lr-pc-4-ag ?? -2 ?????? bnc-rb2 bnc-pr bnc-625/u 10.16 0.05 5.08 0.025 5.08 0.05 5-1.2 +0.1 0 10.16 +0.1 0 12.7 0.05 12.7 0.05 4-3.0 +0.1 0 9.0 +0.1 0 19.1 23 2.5 10.16 10.16 15.0 12.7 17.5 28.2 17.7 2.3 1.1 26.3 12.7 12.7 12.6 1.5 1.4 10.3 11.3 +0.1 0 10.3 12.7 26.3 12.6 1.5 1.4 11.3 +0.1 0 hex dia.12.7 hex dia.12.7 4-3.0 part number finish outer conductor center conductor ug-625/u-cf ag ag ug-625/u-ni-cf ni ag panel thickness1.2 ? 3.5 part number finish outer conductor center conductor ug-604/u-cf ag ag ug-604/u-ni-1-cf ni ag ug-604/u ?????? -3 ug-657/u ug-1094/u bnc-rbp1 bnc-rb 9.6 +0.1 0 8.8 +0.1 0 14.3 26.3 13.7 1.0 1.1 hex dia.12.7 8.5 +0.1 0 9.6 +0.1 0 33 15.1 2.44 14.5 8.5 +0.1 0 9.92 +0.1 0 1.3 27 11.9 1.2 12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 1.6 8.5 +0.1 0 9.6 +0.1 0 32.6 15.2 2.5 2.3 17.4 33 14.5 1.3 1.1 14.4 14.7 8.5 +0.1 0 9.6 +0.1 0 panel thickness0.7 ? 2.4 panel thickness2.2 ? 6.0 ug-604/u ?????? -3 ug-657/u ug-1094/u bnc-rbp1 bnc-rb 9.6 +0.1 0 8.8 +0.1 0 14.3 26.3 13.7 1.0 1.1 hex dia.12.7 8.5 +0.1 0 9.6 +0.1 0 33 15.1 2.44 14.5 8.5 +0.1 0 9.92 +0.1 0 1.3 27 11.9 1.2 12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 1.6 8.5 +0.1 0 9.6 +0.1 0 32.6 15.2 2.5 2.3 17.4 33 14.5 1.3 1.1 14.4 14.7 8.5 +0.1 0 9.6 +0.1 0 part number finish note outer conductor center conductor ug-657/u-cf ag ag independent waterproof with frange o-ring ug-657/u-ni-cf ni ag independent waterproof with frange o-ring ug-604/u ?????? -3 ug-657/u ug-1094/u bnc-rbp1 bnc-rb 9.6 +0.1 0 8.8 +0.1 0 14.3 26.3 13.7 1.0 1.1 hex dia.12.7 8.5 +0.1 0 9.6 +0.1 0 33 15.1 2.44 14.5 8.5 +0.1 0 9.92 +0.1 0 1.3 27 11.9 1.2 12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 1.6 8.5 +0.1 0 9.6 +0.1 0 32.6 15.2 2.5 2.3 17.4 33 14.5 1.3 1.1 14.4 14.7 8.5 +0.1 0 9.6 +0.1 0 panel thickness2.2 ? 3.1 part number finish outer conductor center conductor ug-1094/u-cf ag ag ug-1094/u-d1-cf ni au panel mounting dimensions panel mounting dimensions panel mounting dimensions panel mounting dimensions panel mounting dimensions 6ojunn iuuqxxxeelofudpkq #/$y4fsjft ? 1mfbtfbdlopxmfehfuibuuiftqfdjpdbujpofudpguijtdbubmphnjhiudibohfczuifjnqspwfnfoufudxjuipvuopujdf y.psfpwfs uifdibsbdufsjtujdboeuiftqfdjpdbujpopguifqvcmjtifeqspevdubsfuifsfgfsfodfwbmvft y1mfbtfdpopsnuifdpoufouxjuiuifmbuftuefmjwfsztqfdjpdbujpotxifozpvvtfuifqspevdu
dust cap straight bulkhead cable jack part number finish note outer conductor center conductor bnc-rbp1-cf ag ag independent waterproof with frange o-ring bnc-rbp1-ni-cf ni ag independent waterproof with frange o-ring ug-604/u ?????? -3 ug-657/u ug-1094/u bnc-rbp1 bnc-rb 9.6 +0.1 0 8.8 +0.1 0 14.3 26.3 13.7 1.0 1.1 hex dia.12.7 8.5 +0.1 0 9.6 +0.1 0 33 15.1 2.44 14.5 8.5 +0.1 0 9.92 +0.1 0 1.3 27 11.9 1.2 12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 1.6 8.5 +0.1 0 9.6 +0.1 0 32.6 15.2 2.5 2.3 17.4 33 14.5 1.3 1.1 14.4 14.7 8.5 +0.1 0 9.6 +0.1 0 ug-604/u ?????? -3 ug-657/u ug-1094/u bnc-rbp1 bnc-rb 9.6 +0.1 0 8.8 +0.1 0 14.3 26.3 13.7 1.0 1.1 hex dia.12.7 8.5 +0.1 0 9.6 +0.1 0 33 15.1 2.44 14.5 8.5 +0.1 0 9.92 +0.1 0 1.3 27 11.9 1.2 12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 hex dia.12.7 1.6 8.5 +0.1 0 9.6 +0.1 0 32.6 15.2 2.5 2.3 17.4 33 14.5 1.3 1.1 14.4 14.7 8.5 +0.1 0 9.6 +0.1 0 part number finish note outer conductor center conductor bnc-rb-cf ag ag with frange o-ring bnc-rb-ni-cf ni ag with frange o-ring panel thickness2.2 ? 7.0 panel thickness2.6 ? 6.4 8 bnc-cs-cf 2559-cf (57) m ? ? c-59-cf bnc-jc-cf 2582-cf (20.5) ? bnc-jc-cf/ddk (90) m??bnc? (75) 3.5 markingddk bnc style mating side 605 part number finish bnc-cs-cf ag bnc-cs-ni-cf ni part number finish bnc-jc-cf ag bnc-jc-ni-cf ni part number finish bnc-rc-3 ni bnc-rc-3-d1 ag short cap short cap panel mounting dimensions panel mounting dimensions unitmm http://www.ddknet.co.jp bncseries please acknowledge that the specifcation etc. of this catalog might change by the improvement etc. without notice. moreover, the characteristic and the specifcation of the published product are the reference values. please confrm the content with the latest delivery specifcations when you use the product.
cut the cable as fg.1. please be carefule to not damage the outer conductor. insert the nut, washer, gasket and clamp. the clamp is located on the outer conductor of the cable. pick the outer conductor. cut the insulator and center conductor as fg.3. fold up the outer conductor to the clamp equally and cut the outer conductor of the cable along the clamp as fg.3. please be careful to not damage the center conductor. solder up the contact to the center conductor. please be careful to not be swelled up the solder. please be careful to not gap between contact and insulator. please be careful to not deform the insulator by soldering assembly instruction1 9 insert the body into the above cable assembly and screw up the nut. please screw up the nut by wrench tightly. gasket nut washer clamp male contact plug body female contact jack body gasket clamp mil clamp a b c nut washer gasket clamp body dia. hex dia. cable assembly contact soldering no gap gasket nut washer clamp male contact plug body female contact jack body gasket clamp mil clamp a b c nut washer gasket clamp body dia. hex dia. cable assembly contact soldering no gap parts confgulration applicable cable a 5d-2v, rg-59/u, rg-62/u 10mm 3d-2v, 5d-2w rg-55/u, rg-58/u 15mm 3d-2w 12mm applicable cable b c 3d-2v, 3d-2w, rg-55/u, rg-58/u 6mm 3mm 5d-2v 7mm 5mm rg-59/u, rg-62/u 5.5mm 3mm 5d-2w 7.2mm 5.4mm applicable cable recommended tightening torque 3d-2v, rg-55/u, rg-58/u 117.6 ? 147n?cm(12 ? 15kgf?cm) rg-59/u, rg-62/u, 3d-2w 196n?cm(20kgf?cm) 5d-2v 441n?cm(45kgf?cm) 5d-2w 490 ? 686n?cm(50 ? 70kgf?cm) 6ojunn iuuqxxxeelofudpkq #/$y4fsjft ? 1mfbtfbdlopxmfehfuibuuiftqfdjpdbujpofudpguijtdbubmphnjhiudibohfczuifjnqspwfnfoufudxjuipvuopujdf y.psfpwfs uifdibsbdufsjtujdboeuiftqfdjpdbujpopguifqvcmjtifeqspevdubsfuifsfgfsfodfwbmvft y1mfbtfdpopsnuifdpoufouxjuiuifmbuftuefmjwfsztqfdjpdbujpotxifozpvvtfuifqspevdu
assembly instruction2 10 a b boot ferule center conductor body 15mm 13.3mm 10.6mm 6.6mm 0.51.0mm edge of body edge of crimp dies boot a b boot ferule center conductor body de o body de o cr e boot insert the boot, ferule into the cable and cut the cable as fg.1. please be careful to not damage the outer conductor. cut the insulator and outer conductor as fg.2. pre-solder the center conductor and cut as fg.2. when cutting the insulator, please be careful to not damage the center conductor. solder up the contact to the center conductor. spread the end of the outer conductor to insert the body between insulator and outer conductor easily. please do not pick the outer conductor. please be caredule to not be swelled up the solder. shave the excessed solder along the outside of the contact. please be careful to not deform the insulator by soldering. insert the body into the cable between insulator and outer conductor until the top of the contact is on the same plane with the top of the body and move the ferule to the body. crimp the ferule at position and position . cover the boot on the ferule . a b parts confgulration unitmm http://www.ddknet.co.jp bncseries please acknowledge that the specifcation etc. of this catalog might change by the improvement etc. without notice. moreover, the characteristic and the specifcation of the published product are the reference values. please confrm the content with the latest delivery specifcations when you use the product.
11 assembly instruction3 insert the body into the above cable assembly and screw up the body by the wrench tightly. recommended tightening torque : 196 n?cm(20kgf?cm) contact assembly plug body inserting tool ferule for 2.5d-2v (for 1.5d-2v / rg-179b/u) 17mm 10mm 1mm ferule 2.5d-2v ferule 1.5d-2v,rg-179b/u 20mm a soldering crimping contact assembly plug body inserting tool ferule for 2.5d-2v (for 1.5d-2v / rg-179b/u) 17mm 10mm 1mm ferule 2.5d-2v ferule 1.5d-2v,rg-179b/u 20mm a soldering crimping cut the cable as fg.1. please be careful to not damage the outer conductor. insert the ferule. in case of 2.5d-2v cable, insert the ferule into the cable and push the ferule between sheath and outer conductor until the head of ferule is reached to the sheath by inserting tool(e3001-160) and pick the outer conductor. in case of 1.5d-2v or rg-179b/u cable , insert the ferule until the ferule reached at the sheath and pick the outer conductor. insert the contact assembly into the above cable assembly. solder up the contact with center conductor and crimp the root of the contact assembly. folding down the outer conductor to the ferule and cut the couter conductor along the ferule as fg.3. cut the insulator and center conductor and pre-solder the center conductor. applicable cable a 2.5d-2v 4mm 1.5-2v, rg-179b/u 5mm parts confgulration 6ojunn iuuqxxxeelofudpkq #/$y4fsjft ? 1mfbtfbdlopxmfehfuibuuiftqfdjpdbujpofudpguijtdbubmphnjhiudibohfczuifjnqspwfnfoufudxjuipvuopujdf y.psfpwfs uifdibsbdufsjtujdboeuiftqfdjpdbujpopguifqvcmjtifeqspevdubsfuifsfgfsfodfwbmvft y1mfbtfdpopsnuifdpoufouxjuiuifmbuftuefmjwfsztqfdjpdbujpotxifozpvvtfuifqspevdu
assembly instruction4 12 cut the cable as fg.1. l amm=lmm-12mm remove the sheath please be careful to not damage the outer conductor. insert the ferule and spread the tip of the outer conductor. plunge the sleeve by stripper without diging the edge. cut the center conductor by stripper as fg.4. a b c b d (24.3) (24.3) 15 l la sleeve ferule ferule sleeve *insulator contact crimp crimp area body bayonet delta-mate outer conductor insulator bnc-p mating side (24.3) cable stripper dies a b c b d (24.3) (24.3) 15 l la sleeve ferule ferule sleeve *insulator contact crimp crimp area body bayonet delta-mate outer conductor insulator bnc-p mating side (24.3) cable stripper dies put the contact into the crimp tool attachment and insert it into the crimp dies as fg.7. insert the center conductor into the contact hole and crimp the contact with touching the contact brim to the end of sheath. cut the insulator by stripper as fg.5. insert the stripper and dig the edge to the insulator. rotate the stripper a few times and pull of the insulator. trim the extra outer conductor along the sleeve. insert the above contact assembly into the body until the top of contact is same plane as rim of outer conductor. after the contact brim is inserted into the body, do not rotate the cable and body. put the above cable assembly in the crimp tool and crimp the root of the body. please match the hex of dies with the hole of the body. *the insulator is attached with bnc-p-1.5d-cr10-cf. please cover the sheath when crimping the contact. assembly tool attachment cr-h-1115 cr-h-1116 89134 cr-h-1120a 89141 for cr-h-1120a parts confgulration unitmm http://www.ddknet.co.jp bncseries please acknowledge that the specifcation etc. of this catalog might change by the improvement etc. without notice. moreover, the characteristic and the specifcation of the published product are the reference values. please confrm the content with the latest delivery specifcations when you use the product.
assembly instruction5 nut2 body assembly washer gasket clamp l 1 cable nut1 washer gasket nut1 2 0.3 8 0.3 sheath center conductor outer conductor pre-soldering clamp cut the outer conductor along the clamp outer conductor insulator 12.7 9.5 hex dia. cable assembly body assembly nut1 nut2 soldering body assembly sheath contact center conductor nut2 body assembly washer gasket clamp l 1 cable nut1 washer gasket nut1 2 0.3 8 0.3 sheath center conductor outer conductor pre-soldering clamp cut the outer conductor along the clamp outer conductor insulator 12.7 9.5 hex dia. cable assembly body assembly nut1 nut2 soldering body assembly sheath contact center conductor cable length require for the single ended cable assembly l =l 1 +0.3 1-1.cut the cable as fg.1. 1-2. pre-sollder the center conductor. noteplease be careful to not damage the outer conductor. 1-3insert the nut 1, washer and gasket. 2-1.insert the clamp into the outer conductor and put it on the sheath. 2-2. pick the outer conductor and fold down to the clamp and cut the extra outer conductor along the clamp. 3-1.insert the above cable assembly into the body. 3-2.screw up the nut1 to the body. recommended screw toque117.6 ? 147n?M 12 ? 15kgf?M 4-1.solder up the contact with the center conductor 4-2.screw up the nut2 to the body. recommended screw torque49n?M 5kgf?M 13 parts confgulration 6ojunn iuuqxxxeelofudpkq #/$y4fsjft ? 1mfbtfbdlopxmfehfuibuuiftqfdjpdbujpofudpguijtdbubmphnjhiudibohfczuifjnqspwfnfoufudxjuipvuopujdf y.psfpwfs uifdibsbdufsjtujdboeuiftqfdjpdbujpopguifqvcmjtifeqspevdubsfuifsfgfsfodfwbmvft y1mfbtfdpopsnuifdpoufouxjuiuifmbuftuefmjwfsztqfdjpdbujpotxifozpvvtfuifqspevdu
assembly instruction(6 l 11 (3) 5 0.3 2 0.3 nut1 washer gasket clamp nut2 body assembly cable nut1 washer gasket outer conductor clamp insulator center conductor (pre-soldering) cable assembly 9.52 (hex dia.) 12.7 body assembly soldering nut2 contact slit cable cut the outer conductor along the clamp l 11 (3) 5 0.3 2 0.3 nut1 washer gasket clamp nut2 body assembly cable nut1 washer gasket outer conductor clamp insulator center conductor (pre-soldering) cable assembly 9.52 (hex dia.) 12.7 body assembly soldering nut2 contact slit cable cut the outer conductor along the clamp the cable length require for the single ended cable assembly. l 1 =l+3.3 1-1.insert the nut1, washer and gasket. 1-2. cut the cable as fg.1. noteplease be careful to not damage the outer conductor. 2-1.insert the clamp into the outer conductor and move to the sheath. 2-2.pick the outer conductor equally. fold down to the clamp and cut the extra outer conductor along the clamp. 3-3.cut the insulator as fg. 2. 2-4.pre-solder the center conductor and cut the center conductor as fg.2. 3-1.insert the above contact assembly into the body assembly. notethe center conductor is located in the center of contact slit. 3-2.move the nut1, washer and gasket to the body. 3-2.screw up the nut1 to the body. recommended screw torque117.6 ? 147n?M 12 ? 15kgf?M 4-1.solder up the contact with center conductor. 5-1.screw up the nut2 to the body. recommended screw torque49n?M min. 5kgf?M min. 14 parts confgulration unitmm http://www.ddknet.co.jp bncseries please acknowledge that the specifcation etc. of this catalog might change by the improvement etc. without notice. moreover, the characteristic and the specifcation of the published product are the reference values. please confrm the content with the latest delivery specifcations when you use the product.
assembly instruction7 pre-soldering nut washer clamp washer body assembly nut cable sheath outer conductor washer insulator outer conductor nut washer clamp outer conductor body assembly nut soldering contact slit 15 0.5 3 5.7 +0.5 0 4 0 -0.5 pre-soldering nut washer clamp washer body assembly nut cable sheath outer conductor washer insulator outer conductor nut washer clamp outer conductor body assembly nut soldering contact slit 15 0.5 3 5.7 +0.5 0 4 0 -0.5 the cable length require for the single ended cable assembly l 1 l 1 =l+3 1-1.cut the cable as fg.1. noteplease be careful to not damage the outer conductor. 2-1.insert the nut1, washer1 and insert the clamp on the outer conductor and move to the sheath. 2-2. fold down to the clamp and cut the extra outer conductor in 3 mm from the clamp. 2-3.move the washer 1 and nut 1 to the clamp. 3-1.insert washer 2 on the outer conductor and cut the insulator as fg.3. 3-2. pre-solder the center conductor and cut the center conductor as fg.3. 4-1.insert the above cable assembly into the bodyassembly and screw up the nut 1. recommended screw torque196n?M20kgf?M notethe center conductor is located in the center of contact slit. 5-1.solder up the contact with center conductor. 5-2.screw up the nut 2 to the body. recommended screw torque49n?M5kgf?M 15 parts confgulration 6ojunn iuuqxxxeelofudpkq #/$y4fsjft ? 1mfbtfbdlopxmfehfuibuuiftqfdjpdbujpofudpguijtdbubmphnjhiudibohfczuifjnqspwfnfoufudxjuipvuopujdf y.psfpwfs uifdibsbdufsjtujdboeuiftqfdjpdbujpopguifqvcmjtifeqspevdubsfuifsfgfsfodfwbmvft y1mfbtfdpopsnuifdpoufouxjuiuifmbuftuefmjwfsztqfdjpdbujpotxifozpvvtfuifqspevdu

▲Up To Search▲

Price & Availability of BNC-P-3-NICAU-CF

	To Download BNC-P-3-NICAU-CF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .